2024 Ge oven door lock flashing

quot;Locked Door" is flashing on my GE oven model J TP15B0W2BB. I have turned off the breaker and it did not reset. I have let it self clean and it did not reset. ... I have accidently enabled the self cleaning feature with the oven door open. The lock enabled with the door open and the door will not close. Lock light flashing on GE Oven. Hi - Someone started the clan cycle and stopped it immediately. But the door is not locked even though the display is flashing LOCKED. If I try to start the cycle it seems to be complaining about the door and still flashes locked. Ownership and support information for JB645RKSS | GE® 30" Free-Standing Electric Range. Home Support Range Owner's Center Call Us 1-800-626-2005 Call Us at 1-800-626-2005. View Model Specs. Owner Center | ... If The Oven Door Has Been Locked Accidentally:\tIf there is food in the oven, let the oven cool to r... Read Article.Unplug the washer and locate the lid lock switch, usually beneath the lid area. Remove the old switch and replace it with a new one. Ensure that the new switch is compatible with your GE washer model. After replacement, plug the washer back in and run a test cycle. If the lid lock light no longer flashes, the problem has been fixed.The automatic door lock on my GE oven will not retract after the oven was cleaned. Its Model JKP18. I'm not sure - Answered by a verified Appliance Technician. ... I have a ge model JT3500SF1SS double oven. The door locked keeps flashing but the door is open and will Mott completely close ...Lift the oven door by grasping each side. With the door at the same angle as the removal position (approximately 1” - 2” [2.5 cm – 5.1 cm] from the closed position), seat the notch of the hinge arm into the bottom edge of the hinge slot. The notch of the hinge arm must be fully seated into the bottom of the slot. Fully open the door.So open the door and locate the door/light switch around the frame of the oven. Push the door switch in and hold it so that the oven thinks the door is shut. Now just start a self clean cycle and wait 60 seconds. Then cancel the self clean cycle and the door lock should open.Sometimes shutting off the circuit breaker or fuse in the home that provides power to the range or wall oven for a minute or two will clear the error, fault or function code. …There is a switch mounted on the door lock assembly that may have welded contacts which would tell the control the door is locked. You can access and check the switch by lifting the main top and removing the access panel covering the lock assembly. disconnect the wires from the switch and see if the oven will operate in bake or broil, if it ...Open the oven door and locate the latch hook at the top of the door way above the oven. Wiggle this hard in case it's sticking. Then close the door and try to start self clean again. If it still won't lock the door and the Lock Door light keeps flashing, the door latch needs to be replaced because the door lock isn't locking automatically anymore.My door lock light has been flashing since Wednesday and I can turn it off or open the wall oven door on my GE - Answered by a verified Appliance Technician. ... Locked Door" is flashing on my GE oven model J TP15B0W2BB. I have turned off the breaker and it did not reset. I have let it self clean and it did not reset.Ge profile oven flashing locked door tried cancel and wont turn off ... Have a 7 or 8 year old Electric GE Profile double oven slide in range. I intended to self clean the upper oven. Either the door lock latch was already extended or the oven door was slightly open when ...When it comes to cooking appliances, GE ovens are known for their reliability and performance. However, even the most well-designed and high-quality ovens can encounter issues from...So unfortunately this is a common failure with GE ovens when you self clean. If you've already tried unplugging the unit and that didn't fix the issue, try to wiggle the latch in case it's just jammed slightly and not touching the open position switch. Then try to start a self clean if it will let you and cancel it 60 seconds later.I can't get the oven locked feature to turn off my GE Profile oven. The door will unlock and open, but the light - Answered by a verified Appliance Technician ... I used the self clean feature on the bottom oven and when it was done it kept cycling through the lock and unlock. The locked light is blinking on and off and when I c ...So open the door and locate the door/light switch around the frame of the oven. Push the door switch in and hold it so that the oven thinks the door is shut. Now just start a self clean cycle and wait 60 seconds. Then cancel the self clean cycle and the door lock should open.04 - Dishwasher Door Latch. A dishwasher's lights flashing or blinking could indicate a problem with a micro switch inside the door latch assembly. To determine if the micro switch is at fault, use a multimeter to test the switch for continuity. If the switch does not have continuity, replace it or the entire latch assembly.I have a Kenmore 700 range/oven. I attempted to lock the oven door, but opened the door before the lock was fully engaged. Now the lock is in the locked position, but the door is open. I cannot figure … read moreIf the door is open but the latch is out in the locked position, you can manually attempt to get it back into the unlock position. Open the oven door and find the door switch on the edge of either the upper right or upper left corner. Push and hold in the switch while pressing the "Stop/Cancel" button. Continue to hold in the switch while ...Common GE oven affliction: "Locked Door" light suddenly appeared. Door is not locked, no self-clean was started, lock feature is automatic lock, not a manual latch. I have: a) shut down power via circuit breaker; b) run clean cycle for 3 hours. All to no avail: Locked DOOR light has remained after each attempt.Door locked is flashing, cannot use oven. Oven door is open. I tried pushing the door switch in and going into oven clean mode and then cancelling. Door Locked is still flashing and oven doesn't work. … read moreVideo showing you the parts that make up the door lock system on your stove / range.If you have a stove that won't lock or won't allow you use the self-clean...I don't think that is working. I noticed that my top oven (which is fine) the latch is all the way to the left because it is "unlocked". The bottom oven which has the "locked" signal flashing, that latch is in the middle as if the door is locked even though the door isn't locked..I will keep trying to get it to start the "self clean" but it doesn't seem to be working.Are you a proud owner of GE appliances? Whether it’s a refrigerator, dishwasher, oven, or any other home appliance, understanding the owner’s manual is crucial for getting the most...When your GE lid lock malfunctions, the door will not be automatically open. Wet laundry gets stuck inside, rendering the washer inefficient. If your GE washer lid lock gets stuck, the lid lock mechanism may be jammed or faulty. Wait for the washer to cool and try to open the door or unplug the washer for 60 seconds and plug it back in to reboot.The self-cleaning light, lock light, and/or fan (on models so equipped) may also come on when broiling or baking at high temperatures for long periods of time. Some models have a new, single clean light. There are not separate clean and lock lights. The single clean light will come on as soon as the oven is set for cleaning.GE PT970SS series microwave/oven combo oven door will not unlock. Started self clean mode and door didn't lock completely. Sounds like door lock motor is cycling but won't lock or unlock.Step 4. Open the oven and inspect for any white salt residues. Remove any residue with a damp cloth. If the residue will not come off with a damp cloth, scrub the residue with a soap filled steel wool pad. Follow this with a mixture of half vinegar and half water to completely rinse the oven. References. Writer Bio.Okay, sorry I did not realized the door was actually locked. To stop a clean cycle, press the CLEAR/OFF button and hold for 10 seconds. If the door does not unlock try powering the oven off at the circuit breaker, waiting a few minutes and then powering the oven back on, programming the clock and then press the CLEAR/OFF button and hold for 10 seconds.Hi there. I have a GE Range, model #JGBP88SEK355. For some reason the "Door Locked" notice is flashing, and so I can't use the oven. The door won't close properly either -- it seems the latch is stick … read moreThe lock light has been flashing on my GE profile self cleaning oven for 2 days. I cannot use the oven. When I press the Bake button a DOOR message flashes. This oven is going on 18 years old … read moreStep 3. Push the self-cleaning button and allow the oven to enter the self-cleaning mode. Wait 15 minutes and then press the “Clear/Off” button ending the self-cleaning cycle. The door unlocks once the oven has cooled to a safe temperature. References. Writer Bio.Step 6. Rotate the cam on the door lock mechanism to the unlocked position. Test the resistance between Pin 3 and Pin 1 of the door lock connector with the ohmmeter. The resistance should be 0. Replace Lock Switch 2 of the door lock mechanism if the resistance reads other than 0.Release the door-latching rod by pulling the lock motor assembly down and tilt the front inwards. This will allow you to unhook the locking rod from the drive cam. Push the rod forward and open the oven door. Note the position of the drive cam and the hole that the locking rod fits into. Remove the Philips screw holding the drive cam on the motor.Step 1: Unplug the Oven/Reset Your Breakers. When learning how to unlock an oven door, the first thing to try is to unplug the oven and reset your circuit breaker, as something could’ve gone wrong during a cycle. When an oven has a self-cleaning cycle, it will heat up to 900 degrees to burn away any food debris sticking to the sides of the ...Open the oven door. Inspect the hinge and latch for any visible damage or wear. If you notice any damage, flip the door hinge locks forward with a flat-blade screwdriver. Next, detach the oven door and carefully remove the top and bottom screws. After removing the oven door, you will now have to lift off the inner door, which keeps …My mother has a GE oven with a self cleaning cycle. It has not lever to lock the door. When she or I starts a self cleaning cycle, we hear a motor inside but nothing locks, even when putting pressure on the door. The oven then beeps and flashing LOCK DOOR and does not start the cycle or lock the door. Is there anything I can do to fix this ...The Frigidaire self-cleaning oven has a lock to prevent the door from being opened during the cleaning cycle. The oven door can become locked before and after the cleaning cycle. T...My GE oven has a door locked message flashing when I touch any control. The door is not locked. I just completed a cleaning cycle. ... Model FRS26ZRGWC Serial LA10301441. I went through clean cycle earlier today but my door is locked and Lock light is flashing.And hour later door lock button is flashing and - Answered by a verified Appliance Technician. ... ge electric oven apparently hit self clean button unintentionally while cooking locking latch is engaged but not latched to door (door will open and close) indicator light flashes ...GE PT970SS series microwave/oven combo oven door will not unlock. Started self clean mode and door didn't lock completely. Sounds like door lock motor is cycling but won't lock or unlock. I have turne … read moreNow have flashing door lock icon on display and lower level light will not shut off. I tried shutting off circuit to oven. ... I have a GE Wall Oven that has the door lock light blinking and the lock is in the locked position and won't allow the oven door to close.Press the "9" and "0" in at the same time and hold for 3-5 seconds. If that does not work, flip the breaker off for 2-3 minutes. If that does not unlock the control, there is a software or short in the board. Customer: I flipped the breaker before but not for 2-3 min. Appliance Medic : Yes, try it for a few minutes.Push it in until the oven cavity light goes off, indicating that the oven believes the door is closed. While you hold the door jamb switch in this position, complete the following steps. Press the Self Clean pad and wait 10 seconds. When the Self Clean cycle initiates, press the Clear/Off or Cancel pad immediately to cancel it.Apr 3, 2019 ... Bypass the Stupid F9 Error Code Oven Door Lock!!! 116K views · 5 years ago ...more. Pinche Culero. 244.Ge oven display is flashing between probe and bake .itgoes off when i press clear off. it goes off for a few - Answered by a verified Appliance Technician ... My GE oven, item #JKP30SMSS, door has gone into the lock mode. My GE oven, item #JKP30SMSS, door has gone into the lock mode and I can't open it. I had baked some bread in it, ...From https://www.justanswer.com/ythiJustAnswer Customer: I can't get the oven locked feature to turn off my GE Profile oven.JustAnswer Customer: The door wil..."LOCKED DOOR" light flashing continuously. Door lock is open. Oven door will close. SELF CLEAN will not function but asks me to set timer.If I try to set the BAKE or BROIL function a green "door" light comes on. Nothing functions. A service tech came out, looked at the oven and told me he would have to replace the control board at a cost of ...We have a GE Double Oven unit with range top & control panel @ the rear, mod P B9787 P4SS, Ser GT2 39973Q. While wiping the control panel with a damp dish cloth to clean it, the door lock symbol for t … read moreShouldn't have to lock door for steam clean just POUR 1 CUP of water at bottom of the oven cavity and press steam clean then start. If that doesn't work unplug for 30 minutes to restart control panel and try again. Also looks like the lever isn't all the way to the right. My 10 year old GE wall oven flicks on and off.Here's how to do it: Step 1 - Let the oven cool down. Before doing anything, give your oven an hour or so after the self-cleaning cycle has ended so that it can properly cool down. This is because the oven will be too hot to work with until it has cooled down completely. Step 2 - Cut the power.F-4 Shorted oven sensor or harness Replace the oven sensor F-5 Power to element relay disabled in cook mode Replace the clock/relay board F-7 Shorted touch pad key sensed for 32 secs. Replace the touch pad/control panel F-8 Shorted meat probe Replace the probe jack. F-9 Door lock safety circuit on ERC sensed Replace the door latch assembly01 - Boot Seal Retaining Ring. A washer door boot seal retaining ring is the component that secures the door boot seal to the front panel on front-load washing machines. If the retaining ring is damaged or missing, the boot seal can become detached from the panel and prevent the door from closing and locking properly.Ownership and support information for PT7800SHSS | GE Profile™ 30" Built-In Combination Convection Microwave/Convection Wall Oven Home Support Wall Oven Owner's Center Call Us 1-800-626-2005 Call Us at 1-800-626-2005A washer door boot seal retaining ring is the component that secures the door boot seal to the front panel on front-load washing machines. If the retaining ring is damaged or missing, the boot seal can become detached from the panel and prevent the door from closing and locking properly. If the retaining ring is missing or broken, you should ...I went to set the oven clean cycle but opened the oven door before it could lock. ... Ge profile oven. When I opened the oven door the lock engaged and now the door cannot close and the locked light is flashing. I unplugged it to try to reset it - didn't work. ... My electric range keeps flashing "door locked" and the oven doesn't work.My door lock light is flashing, and I can't get my door closed...the lock is out and won't go back in. GE JT3500. - Answered by a verified Appliance Technician. We use cookies to give you the best possible experience on our website. ... Ge profile oven. When I opened the oven door the lock engaged and now the door cannot close and the locked ...This is a preview of a video that shows you how to Diagnose and Repair a *JB655SK3SS GE Stove WB14T10092 Door Latch Assembly**Symptoms may include:* Unit Not...My GE self cleaning oven has started beeping, showing F2 and flashing "locked door" on the screen. This was about - Answered by a verified Appliance Technician ... Whirlpool Super Capacity 465 electric oven went into self-clean, by accidental push of the button, and when I heard the door lock, I pushed cancel and waited for it to cool down and ...The panel is flashing "LOCK" on a GE Profile JT965 oven.microwave combo. I can hear the lock motor running. None - Answered by a verified Appliance Technician. We use cookies to give you the best possible experience on our website. ... Have a GE Profile JT955 oven. Door lock is set with locked flashing in display. Door is open (we are afraid to ...Lock light flashing on GE Oven. Hi - Someone started the clan cycle and stopped it immediately. But the door is not locked even though the display is flashing LOCKED. If I try to start the cycle it seems to be complaining about the door and still flashes locked.These codes help GE Appliance Service technicians to more quickly diagnose issues with the Advantium. Below are the most common fault codes: 120v Fault Codes. Definition. F1. Open Thermal Sensor. F2. Shorted thermal sensor. F3.My GE stove is beeping and light flashing door locked...I have unplugged the stove for 1 minute no success still beeping until i hit the clear button and then starts again ... My Kenmore oven Model #79095651001 is flashing the lock button. Now my oven does not work. ...View All Brands Whirlpool Parts Kenmore Parts Frigidaire Parts GE Parts LG Parts. ... Magic Chef "Lock" flashing - The oven door is not latching for the self-clean cycle. 01 - Door Latch. Required Part. Range/Stove/Oven Door Latch. Enter model number to search for the required part specific to your product.Ownership and support information for JS968SKSS | GE Profile™ 30" Slide-In Electric Range. Home Support Range Owner's Center Call Us 1-800-626-2005 Call Us at 1-800-626-2005. View Model Specs. ... Oven Door Will Not Unlock. If The Oven Door Has Been Locked Accidentally:\tIf there is food in the oven, let the oven cool to r... Read Article.its the door lock. the switches you see on the lock assembly are for the clean and cook. when the switch for the lock for clean cycle doesnt shut of it will think the door is locked and wont go to bake.if you look at the picyure you can see the cams and the switch fingers its probably in between locked and unlocked. the motor may have burned ...ge profile wall oven model PK7000SF6SS I used the self clean oven feature yesterday. a red blinking light, says door, shows a lock. When I shut the door it makes a buzzing sound. clock is working, not … read moreHave a GE oven model JKP15BW with a door lock motor problem I think? It keeps flashing "locked door" but door is not locked and I can here a slight humming noise where the lock motor is. Also if I open the door, hold the switch in to make it think the door is closed and then push the switch a little to the right the humming stops.My locked is flashing on ge oven, door - Answered by a verified Appliance Technician. We use cookies to give you the best possible experience on our website. ... The lock light has been flashing on my GE profile self cleaning oven for 2 days. I cannot use the oven. When I press the Bake button a DOOR message flashes.GE PT970SS series microwave/oven combo oven door will not unlock. Started self clean mode and door didn't lock completely. Sounds like door lock motor is cycling but won't lock or unlock. I have turne … read moreF-4 Shorted oven sensor or harness Replace the oven sensor F-5 Power to element relay disabled in cook mode Replace the clock/relay board F-7 Shorted touch pad key sensed for 32 secs. Replace the touch pad/control panel F-8 Shorted meat probe Replace the probe jack. F-9 Door lock safety circuit on ERC sensed Replace the door latch assemblyGE Oven Error Code: Loc Door. If a “LOC DOOR” message is flashing in the display of your range or wall oven and the self-clean cycle has not been selected, please check to …Second opinion] I have 21 year old GE microwave oven which is flashing door locked on oven but is not. I tried to - Answered by a verified Appliance Technician ... GE Profile oven/microwave wall combo.....oven door is locked - flashing "door lock" on the panel.....the oven is not on.....it will not unlock, the oven is not operable.The self-cleaning light, lock light, and/or fan (on models so equipped) may also come on when broiling or baking at high temperatures for long periods of time. Some models have a new, single clean light. There are not separate clean and lock lights. The single clean light will come on as soon as the oven is set for cleaning.Help! Whirlpool WTW5010LW - sense, lid lock and done lights flashing. I tried to wash a comforter and blanket and when I went back check the load the lid was locked and those three lights were flashing. I unplugged the Washer because nothing else I did would get the lid to unlock. After powering down the lid did unlock, and I removed the ...Let us try this to get you going again. open the door all the way, then with one hand hold the door button for the oven light in and do not let go, then with the other hand start a self clean cycle, after about one minute cancel the self clean cycle and wait to see it the latch goes back in and the door lock light goes out, then release the door button that you have been holding all this time...Jun 5, 2019 · GE Profile oven has "locked" flashing, but door is not locked, and oven will not allow me to set a baking temp, or start a self-cleaning cycle. It has Auto door lock, not a latch. read more You can perform a reset by shutting off the breaker that supplies power to your oven. Turn off the breaker in your home's electrical service panel and leave it off for a full 30 seconds. Then, turn the breaker back on. In addition to resetting your oven, this measure will force your oven to double-check its own diagnosis.Hello I'm Larry and I will use all my training and knowledge of 40 years to help you with your Problem today ,, thanks open the door, press and hold the door switch, set the oven to self clean and turn on, once the latch comes out the locks then cancel the clean cycle, once the latch draws back in then turn loose of the door switch and it should be fineYour oven's owner manual may also have a way to reset it via pushing specific buttons on the control panel as well. Finally, if none of the above worked, it is possible that the door lock is malfunctioning. In most ranges, you can access this by removing the top of the stove, though some models may have access in the back of the appliance.Should the automatic self-clean lock engage and lock the oven door during a bake cycle, press the CLEAR/OFF pad and allow the range or wall oven to cool to room …To unlock a GE Profile dryer Whirlpool, press and hold the Extended Tumble and - (minus) buttons for 3 seconds. The control lock icon will flash while locking/unlocking, stay on when locked, and turn off when unlocked. If your dryer does not have an Extended Tumble button, consult your owner's manual for instructions on how to unlock the ...To lock a GE oven door, press and hold the "Lock" button for 3 seconds. This will prevent the door from being opened until the lock is released. Step 3: Engage the Door Lock. With the door lock lever located, the next pivotal step in securing your GE oven is to engage the door lock mechanism.When it comes to home security, one area that often gets overlooked is the locking mechanism on your external doors. While traditional locks can provide a basic level of security, ...

Step 4. Unplug the range and wait 60 seconds if the display keeps blinking. Restore power and try to set the clock again. Contact GE at 800-848-7620 if the control panel keeps flashing. GE ranges come in gas and electric models and various configurations, such as slide-in, freestanding or drop-in, and have many cooking features and options.. Crawfordsville in craigslist

The door lock for oven cleaning is blinking and I can't get it to go off. I have tried to set the clean time and it won't lock the door and keeps flipping back to the correct time. ... I have the GE profile double wall oven. I ran the self clean cycle on both ovens and now the locked light on the bottom oven keeps blinking and some type of fan ...F5 Error: Door Lock Failure. Sometimes the oven fails leaving the door in a mechanically locked condition. I will defer to my colleagues who make service calls to comment on some tricks to fix the mechanics of this. There are two limit switches on the lock mechanism which tell the controller whether the door is open, closed or locked.The lock striker fits inside the lid lock and ensures the lid is closed. Without this small piece, your washer would run even if the lid were open. The lid striker is located along the edge of the lid. A lid that opens indicates that the problem lies with the lid striker. Look for detergent and lint built up around the striker or the lock.Lock light on panel of GE drop in Oven won't stop blinking red; oven door won't fully close, so latch won't - Answered by a verified Appliance Technician. ... Lock light on panel of GE drop in Oven won't stop blinking red; oven door won't fully close, so latch won't engage. I think it's a latch problem ..I have turned off breaker ...Release the door-latching rod by pulling the lock motor assembly down and tilt the front inwards. This will allow you to unhook the locking rod from the drive cam. Push the rod forward and open the oven door. Note the position of the drive cam and the hole that the locking rod fits into. Remove the Philips screw holding the drive cam on the motor.I was doing a self-cleaning on my GE Profile oven and it has started beeping and flashing F2? What does that mean - Answered by a verified Appliance Technician ... And also once the self clean setting is programmed and started does the oven in fact lock the oven door and does the door locked light illuminate ? ... I am about 1.5 hours into a ...We have a ge monogram double ovens ZEK7500 my wife ran cleaning cycle, when cooled she opened the over door to wipe out. The red door lock was still flashing but door opened. The lock light wouldn't t … read moreMy GE Profile double oven is flashing door lock after a self cleaning cycle. Contractor's Assistant: I understand that your GE Profile double oven is flashing 'door lock' after a self-cleaning cycle. Is the oven door currently locked? I can open the door but when I close it there is a rattling sound and the oven light does not turn offTo set the oven Lock feature (instructions may vary by model – check your Owner’s Manual for more details): Press OFF and hold for 6 seconds. Lock will appear in the display, the door locked indicator light will flash, and the door lock will begin to close. Allow about 15 seconds for the oven door to lock. Once the oven is locked, the ...GE Oven Door Won't Unlock/Locks Intermittently. The part(s) or condition(s) listed below for the symptom Oven door won't unlock/locks intermittently are ordered from most likely to least likely to occur. Check or test each item, starting with the items at the top of the page. Related Videos. Symptom;Press the CLEAN or SELF CLEAN pad or turn the selector knob to CLEAN on the oven control for older models. After a few seconds the words LOCK DOOR appear on the control panel and/or the LOCK light will come on. The oven will turn off automatically when the Self-Clean cycle is complete. The door will stay locked until the oven has cooled down.The door lock light keeps flashing, but the doors are not locked - Answered by a verified Appliance Technician. We use cookies to give you the best possible experience on our website. ... The bottom oven of my ge profile double wall oven will not clean, but has locked and will not unlock. The locked signal keeps flashing.To set the oven Lock feature (instructions may vary by model - check your Owner's Manual for more details): Press OFF and hold for 6 seconds. Lock will appear in the display, the door locked indicator light will flash, and the door lock will begin to close. Allow about 15 seconds for the oven door to lock. Once the oven is locked, the ...After 30 seconds, the user will notice that the display on their device shows the word “loc”. This indicates that the doors are now locked, and your lights should also stop blinking. You can then hold the same button for another 3 seconds and wait. This should unlock the doors and allow you to start using the device. Pull to your left until it becomes loose and noticeably 'broken'; this is the correct procedure. Pros: Door lock now broken. Light disabled. Full use of oven restored. Removed wife's threat of calling repairman at $50 an hour Cons: can't use "Self Clean" anymore. Fer O'Neil. Fix Flashing "Locked Door" Light GE Profile Oven. My Kenmore stove electric range is showing the lock flashing on the display panel. The oven still works and all other buttons work but the elements are locked out. ... I have a Kenmore Elite 40" Dual Fuel double oven range and I can't get the door to lock for the oven cleaner to engage. ... ge electric oven apparently hit self clean button ...ge profile wall oven model PK7000SF6SS I used the self clean oven feature yesterday. a red blinking light, says door, shows a lock. When I shut the door it makes a buzzing sound. clock is working, not … read moreTry adjusting the cam (the main shaft of the lock) on your oven door lock mechanism to the unlocked position. Using a multimeter, measure the resistance between Pin 3 and Pin 1 on the door lock connector. Ideally, the resistance should be zero. If it’s not zero, then Lock Switch 2 on your door lock mechanism might need to be replaced.My GE profile oven Model JMP31W0A2WW lock light is flashing, and wont turn off. I have unplugged started clean cycle and cancelled the during the clean cycle the oven did not heat up and the oven door … If your oven has an automatic lock, it should only engage during the self-clean cycle. Should the automatic self-clean lock engage and lock the oven door during a bake cycle, press the CLEAR/OFF pad and allow the range or wall oven to cool to room temperature. Once cool, see if the automatic lock has released by trying to open the oven door. .

Popular Topics